Kindle DX update blues

-

A few days ago I received a letter from Amazon stating a new firmware was available for Kindle, and that those with coverage problems with Whispernet could get the update file from the web too.

Firmware update for Kindle is supposed to be quite a straightforward operation. First, update file is downloaded to your Kindle, either wirelessly or manually by the user, to the main folder of the system. Once in there, either because user request or automatically, update process starts.

I've done this before and no trouble happened then. This time was different, though. I mentioned on a previous post that I've played with the USB networking hack, that enables network access to the Linux system running in the Kindle. I did some tests, set the correct system time on my Kindle and forgot about it.

Now that I was trying to update from version 2.3.4 to the new 2.5.2 version I was stucked. Update process stated normally, and "stage 1 of 3" was shown on the lower right corner of the display, but a few seconds later the process stopped with an error message and the error code U006 was shown on the lower right corner.

Several minutes later it was clear the problem was due to a checksum error of one of the system config files. I vaguely remember I did some minor changes to several files, but months later I could not remember what I might have done and to what files.

Luckily there was a way to find out where the problem was. System logs are accesible by the debug command ;dumpMessages that will create a new "book" with the contents of the log file. A careful reading of which led me to discover the file causing the trouble was framework.mario.conf.

Again, thanks to Mobilread forums I've obtained the original file, that though did not have the expected MD5 sum, it worked flawlessly. It is a shame the whole process took me a couple of afternoons to figure out.

I guess the moral of the story is that if you fiddle with your Kindle´s internals, please backup any file before changing it and keep a clean record of what you did.

Comments

Josemanu said…
Ahora que llega el verano ¿estás pensando en algún proyecto basado en Arduino?.
No se si lo sabes pero se está intentando formar una comunidad física de usuarios.
Este viernes tenemos "reunión" aquí: http://arduinobarcamp.jottit.com/
1:07 pm
misan said…
Gracias Josemanu,

Ya me he apuntado. Llevaré un par de proyectos que tengo por casa.
1:22 pm
Post a Comment

Popular posts from this blog

VFD control with Arduino using RS485 link

-
Image
Variable Frequency Drives ( VFD ) allow the control of spindles so speed can accurately be controlled and a detailed acceleration profile for the spindle and reverse rotation can all be handled. In essence a VFD is an three phase inverter for three-phase AC motor. I am using a popular (I mean cheap) Chinese VFD and though the reference manual is not great, I could see there is a built-in RS-485 port. I usually control the start, stop and speed selection using the keyboard on the unit but I thought it will be more useful if I could control everything from the same Arduino is doing our CNC table control. Some cheap RS-485 off eBay and some lines of code later, I can start, stop and change the speed from an Arduino. What a cool thing to have! Some configuration of your VFD are needed before you can use it like that.  You need to set PD163=1 (I am using address 1 in the code). PD=164=1 (for setting serial to 9600bps) and PD165=0 (for using ASCII and 8N1 character format)
Read more

How to get sinusoidal s-curve for a stepper motor

-
Image
After some experimentation, and delving a bit into the math of motion, I realized there can be a significant difference on the motion of a machine by just making small changes. A common and popular approach to smooth one axis of motion is to use a trapezoidal speed pattern, where acceleration and deceleration are uniformly accelerated movements (aka constant acceleration motion) separated by a portion happening at cruising speed. The problem comes with the fact that, while that approach is simple to understand and to code, it does contain sudden changes in the acceleration, that show as spikes on the acceleration derivative, called jerk. These sudden changes in the acceleration translate into undesired vibration in our machines. Most of that can be eliminated by selecting a motion pattern that does not contain sudden changes of acceleration. If we chose a mathematical function for our speed whose second derivative is continuous, then we reduce system vibration quite a lot. One ma
Read more

Importing OpenSCAD designs into Onshape

-
Image
After using Onshape CAD software for a while I am really fond of it. So one natural thing to do, specially once they have released the Instructor's kit is to start using it in the classroom too. But one thing I was not so sure how to do was to use old designs I made using OpenSCAD. It does not mean I am completely quitting using OpenSCAD but suddenly I can see I can do assemblies in Onshape that will look quite nice for showing and documentation purposes if only I could easily import from OpenSCAD. I am glad to report that the route OpenSCAD --> FreeCAD --> Onshape worked brilliantly. Even more when a few tricks were applied. While some people suggest to import CSG files from OpenSCAD to FreeCAD, I have had more success by directly importing SCAD files into FreeCAD. One trick that worked well for me was to get rid of $fn references, so now circles become real circles (or cylinders) in FreeCAD. If a part keeps some $fn references then your cylinders or circles wi
Read more