Fighting with Ubuntu 6.06

-

After some success on my laptop and using the released version, I have decided to install Ubuntu 6.06 on my main computer at the office that has been happily running SuSE Linux 10.0. I guess it is against my own advice (and common sense) to install a new software when the old one was giving you a good service, but I can't help it, I enjoy trying out new software versions (maybe I'll have to start a branch for "Installers Anonymous").

There is always a catch: My hard drive does not have space available and I really would like to keep SuSE Linux just in case. After all I have lots of stuff installed and working, like VMware or CrossOver Office and I do not know whether all these will run trouble-free on Dapper Drake (DD is the name of Ubuntu's 6.06) or not. I know from experience that VMware use to be quite picky about kernel versions.

So I needed some free space on my hard drive before I could install Ubuntu. Catch 2: I could not resize my Linux partition from SuSE Linux 10.0 as it is a mounted partition when running the system. You cannot resize a partition while it is mounted (or should I say you should not do it). Catch 3: My Knoppix 3.8 does not handle reiser filesystem resizing. So I cannot use the nice QTParted that comes with this version of Knoppix (I am almost sure this was fixed in later versions but unfortunately I did not have a copy of the latest version at hand nor the time to download and burn a CD with it). So I had to backtrack to "resize_reiser" which reduces an existing filesystem so you can later resize your partition (by the scary process of deleting it and recreating a smaller one using fdisk). Please note that a mistake here may be big trouble if your filesystem is larger than the partition space you allocate for it (be careful and double check your numbers).

I was lucky and I get 30 GB of space freed for my new OS. So I grabbed Ubuntu's LiveCD and I followed through the install process choosing a manual partitioning and creating a new partition on the room I had created previously. It all worked as expected and now I have one Ubuntu and one SuSE entries (sorry, no windows here) on my GRUB boot menu.

Once I booted Ubuntu I was told several software and security updates were available and I choose them. Catch 4: Selecting a screensaver locked the system to a hardware reset. Not a good start. But, again, the reason was poor support of my graphics card 3D functions on the "ati" driver (I know there is a better driver choice but that was the default I got from the install).

I have used the same /home partition I was using with SuSE so all my data and configuration is there (almost). I was using KDE with SuSE and now I am using Gnome with Ubuntu so some othe desktop icons are not working as they are calling the wrong binaries (it's time to tidy up the desktop a bit).

While I am pleased with the tools I have got installed; I realize I need to install some extra applications. For that, I have found very useful the information on this guide. I have installed the following software for the moment:
  • Texmacs scientific document editor.
  • Lyx (a latex front-end) text editor.
  • Gnuplot (I use it a lot for simulation graphs).
  • gstreamer0.10-fluendo-mp3 (guess what it is for :^)
  • flash-nonfree firefox plugin (so I can browse your youtube videos)
  • inkscape (a great SVG graphics editor)
Oops, I have also installed the weather/temperature applet on the top panel and it shows a storm sing and I have to bike home ... I better hurry up.

Comments

Post a Comment

Popular posts from this blog

VFD control with Arduino using RS485 link

-
Image
Variable Frequency Drives ( VFD ) allow the control of spindles so speed can accurately be controlled and a detailed acceleration profile for the spindle and reverse rotation can all be handled. In essence a VFD is an three phase inverter for three-phase AC motor. I am using a popular (I mean cheap) Chinese VFD and though the reference manual is not great, I could see there is a built-in RS-485 port. I usually control the start, stop and speed selection using the keyboard on the unit but I thought it will be more useful if I could control everything from the same Arduino is doing our CNC table control. Some cheap RS-485 off eBay and some lines of code later, I can start, stop and change the speed from an Arduino. What a cool thing to have! Some configuration of your VFD are needed before you can use it like that.  You need to set PD163=1 (I am using address 1 in the code). PD=164=1 (for setting serial to 9600bps) and PD165=0 (for using ASCII and 8N1 character format)
Read more

How to get sinusoidal s-curve for a stepper motor

-
Image
After some experimentation, and delving a bit into the math of motion, I realized there can be a significant difference on the motion of a machine by just making small changes. A common and popular approach to smooth one axis of motion is to use a trapezoidal speed pattern, where acceleration and deceleration are uniformly accelerated movements (aka constant acceleration motion) separated by a portion happening at cruising speed. The problem comes with the fact that, while that approach is simple to understand and to code, it does contain sudden changes in the acceleration, that show as spikes on the acceleration derivative, called jerk. These sudden changes in the acceleration translate into undesired vibration in our machines. Most of that can be eliminated by selecting a motion pattern that does not contain sudden changes of acceleration. If we chose a mathematical function for our speed whose second derivative is continuous, then we reduce system vibration quite a lot. One ma
Read more

Importing OpenSCAD designs into Onshape

-
Image
After using Onshape CAD software for a while I am really fond of it. So one natural thing to do, specially once they have released the Instructor's kit is to start using it in the classroom too. But one thing I was not so sure how to do was to use old designs I made using OpenSCAD. It does not mean I am completely quitting using OpenSCAD but suddenly I can see I can do assemblies in Onshape that will look quite nice for showing and documentation purposes if only I could easily import from OpenSCAD. I am glad to report that the route OpenSCAD --> FreeCAD --> Onshape worked brilliantly. Even more when a few tricks were applied. While some people suggest to import CSG files from OpenSCAD to FreeCAD, I have had more success by directly importing SCAD files into FreeCAD. One trick that worked well for me was to get rid of $fn references, so now circles become real circles (or cylinders) in FreeCAD. If a part keeps some $fn references then your cylinders or circles wi
Read more