Direct drive extruder

-
Once I have got my Prusa Mendel 3D printer working, I have started to look around for improvements. The thing I was less happy with was the clunky extruder, made of a geared drive with printed gears. People in the forums mention it has a limited life of maybe one hundred hours before one or more teeth give in.

I thought a direct drive was an obvious choice only if extruder stepper might have enough torque. Then I learned that Orca v0.3 is using a direct drive using a brass insert. I looked for available designs on the Thingiverse for NEMA 17 motors and I have found this one. With some changes I have made it work.

But not before I replaced one StepStick by a Pololu stepper driver on my RAMPS board. The reason is that to achieve the required torque, the motor needs to be driven slightly above the 1A limit of StepSticks. The other required change is to add some cooler to the A4988 chip so it can properly dissipate the additional heat.

I guess 3mm filament is quite more challenging to make it work with a direct driver extruder than 1.75mm one.


Update: I designed a replacement for the extruder above that uses much less plastic that hopefully will perform better too. The replacement was printed using the yellow extruder part you can see being printed in the video above.

Comments

nophead said…
I find ABS gears last many thousands of hours if you keep them lubricated with lithium grease.
6:15 pm
misan said…
That is perhaps the next stop. I do not like to push the electronics to the edge (temperature-wire).

I've seen some ABS gears from an old printer paper-feed roll I might end up recycling too. Or maybe I will switch to 1.75 mm.

Thanks,

misan
6:29 pm
Cadisch Screens said…
Great work, I love seeing it in action.
5:52 pm
Post a Comment

Popular posts from this blog

VFD control with Arduino using RS485 link

-
Image
Variable Frequency Drives ( VFD ) allow the control of spindles so speed can accurately be controlled and a detailed acceleration profile for the spindle and reverse rotation can all be handled. In essence a VFD is an three phase inverter for three-phase AC motor. I am using a popular (I mean cheap) Chinese VFD and though the reference manual is not great, I could see there is a built-in RS-485 port. I usually control the start, stop and speed selection using the keyboard on the unit but I thought it will be more useful if I could control everything from the same Arduino is doing our CNC table control. Some cheap RS-485 off eBay and some lines of code later, I can start, stop and change the speed from an Arduino. What a cool thing to have! Some configuration of your VFD are needed before you can use it like that.  You need to set PD163=1 (I am using address 1 in the code). PD=164=1 (for setting serial to 9600bps) and PD165=0 (for using ASCII and 8N1 character format)
Read more

How to get sinusoidal s-curve for a stepper motor

-
Image
After some experimentation, and delving a bit into the math of motion, I realized there can be a significant difference on the motion of a machine by just making small changes. A common and popular approach to smooth one axis of motion is to use a trapezoidal speed pattern, where acceleration and deceleration are uniformly accelerated movements (aka constant acceleration motion) separated by a portion happening at cruising speed. The problem comes with the fact that, while that approach is simple to understand and to code, it does contain sudden changes in the acceleration, that show as spikes on the acceleration derivative, called jerk. These sudden changes in the acceleration translate into undesired vibration in our machines. Most of that can be eliminated by selecting a motion pattern that does not contain sudden changes of acceleration. If we chose a mathematical function for our speed whose second derivative is continuous, then we reduce system vibration quite a lot. One ma
Read more

Importing OpenSCAD designs into Onshape

-
Image
After using Onshape CAD software for a while I am really fond of it. So one natural thing to do, specially once they have released the Instructor's kit is to start using it in the classroom too. But one thing I was not so sure how to do was to use old designs I made using OpenSCAD. It does not mean I am completely quitting using OpenSCAD but suddenly I can see I can do assemblies in Onshape that will look quite nice for showing and documentation purposes if only I could easily import from OpenSCAD. I am glad to report that the route OpenSCAD --> FreeCAD --> Onshape worked brilliantly. Even more when a few tricks were applied. While some people suggest to import CSG files from OpenSCAD to FreeCAD, I have had more success by directly importing SCAD files into FreeCAD. One trick that worked well for me was to get rid of $fn references, so now circles become real circles (or cylinders) in FreeCAD. If a part keeps some $fn references then your cylinders or circles wi
Read more